build diary

July 16, 2004:
The front fenders in place.
These will cover a 205 tire but the offset needs to be correct.
entry 469
Using a nibbler to create the holes for the console switches.
This was much easier than I had feared.
entry 470
All controls in place!
In front of the gearshift from left: Ignition, starter button, hazard lights. Behind the shifter, turn indicator, headlights, high/low switch and brake bias adjuster. The piece of tape marks out one of the crossbars in the transmission tunnel.
entry 471
Installing the Dzus fastener for the nose cone.
First, drill a hole through both parts so that the end result is aligned.
entry 472
The Dzus fastener temporarily held in place.
The countersunk hole gets quite close to the trailing edge of the nose cone. This recessed lip on the nose really could be 1/2" longer to make this easier to fit.
entry 473
The Dzus spring is riveted in place.
entry 474

July 18, 2004:
Whew.
Saturday was a lot of cutting and fitting. I decided to tackle the header as it's the last big job remaining. Armed with a chop saw, a grinder, a welder and a lot of patience I managed to get all four runners built. They're only tack-welded together and are still missing an exhaust flange, but the hard part is done. I have to say that I'm very proud of this. I managed to get three of the runners at the ideal length and the other is only 10mm longer. It looks good and should help my engine breathe as well as possible. There's no way I could have honestly built this any other way than by cutting and welding u-bends. It's also just as well I wasn't paying someone else by the hour - it took me at least 8 hours to get it done! Now I just have to finish the rest of the exhaust...

About those ill-fitting aluminum panels. Both my friend Eric and I realised at the same time that the problem pieces are those that are probably exclusive to the Miata kit. Steve at CMC mentioned that they were mocked up on that 2-day GRM build in the shop. Sounds as if there were some time pressures...
entry 475

Time for some header construction! Here are the pieces for the #4 runner.
entry 476
The #4 runner in place.
entry 477
The #3 runner is done.
I'm not thrilled about a small kink in this one, mostly from an aesthetic point of view.
entry 478
The #2 runner.

entry 479
I decided to move the #2 runner to #1.
I thought I had the ideal routing but this works better.
entry 480
#1 does get a little close to the brake line.
I'll build a shield for this.
entry 481
Cutting and more cutting.
entry 482
The complete header!
entry 483
The only compromise I had to make in length.
About 10mm (3/8") of extra length in the #2 runner. Reaching that position in the collector proved to be very challenging.
entry 484

July 19, 2004:
The exhaust system is complete!
Well, almost. I still have to open up the holes in the flange for the larger 2.5" tube, but then I can start welding everything together permanently. Hopefully without any real distortion! I'm still quite chuffed about how the header turned out - I can see a couple of small changes I'd make now, but nothing that makes it worth reworking. The muffler has been hung beside the driver and I've even managed to put together a tip. Soon enough I'll discover just how loud this thing is! Since a few people have asked, the individual runners for the header will remain individual. The join at the collector is a slip joint. While it will be a little more prone to leaking this will make it possible to remove and replace the header without pulling the engine!

As a short break from all the cutting and welding, I also fitted the tail lights to the car. It's coming together now, and quickly. I'm almost ready to send the body parts off for painting.
entry 485

My heat-shielded brake line.
An aluminum shield plus reflective wrap. This should do the trick.
entry 486
Another view of the header.
entry 487
The complete exhaust system is in place.
entry 488
A change from all the exhaust system photos, here's the rear of the car.
The tails are straight, they just look funky in the photo.
entry 489
<< | show individual entries | >>