build diary

July 4, 2004:
No radiator or body panels, but here are the results from the scales.
Less than I'd expected!
entry 411
Before driving, a rough alignment.
This is not a quick job as the suspension needs to be disassembled. In the rear this is difficult. The front was much easier.
entry 412
Out of the garage! The battery was tired so we had to jump the Seven with Brian's S-10.
entry 413
Miata meets the Seven!
entry 414
I expected the Seven to look smaller, but it's big for this type of car.
entry 415
No, we didn't bother aligning the steering wheel.
entry 416
Not a big car.
Brian checks out a leaking coolant line.
entry 417
The Land Rover and the Seven.
Somehow I don't think it's going to be difficult to decide which one to take for a given trip.
entry 418

July 6, 2004:
After all the excitement of the first drive on the 4th, I took the day off to do other things.
Well, mostly. I did find the time to change the upper control arm on the right rear wheel. I had to replace the right rear upper arm when the original was found to have a misaligned bracket. Well, the bracket that was used for the replacement was drilled further out than the original arm for the left side. Luckily the left side part will fit the right if it's flipped upside down. Installing it gave me an extra 1.5 degrees of negative camber, putting the alignment right where I wanted it.
entry 419

Building the steering wheel adaptor.
entry 420
The steering wheel adaptor installed.
It's fairly minimalist!
entry 421
Here's why there was no negative camber in one wheel.
These are two upper control arms compared. The one with rod ends in it is too long.
entry 422
The original left side upper control is flipped upside down and mounted on the right wheel.
This gave an extra 1.5 degrees of negative camber, putting the car right where I wanted it.
entry 423
Test fitting a front fender.
entry 424

July 7, 2004:
I chopped up the factory exhaust manifold last night.
I'm not sure if I want to use the collector from it or not. I could obviously do better but I certainly couldn't pay less! 10 feet of pool hose is being used to mock up the header and determine pipe routing but it's a bit like wrestling a blue octopus that's lost a few tentacles. This is the first time I've tried to build a header of any sort and it's obviously a bit of an art.
entry 425

The factory exhaust manifold comes apart.
Reluctantly.
entry 426
The 4-1 collector for the factory manifold.
Not too bad for a free part.
entry 427
Using pool hose to mock up the header.
It's quite a challenge getting everything tucked into place.
entry 428

July 8, 2004:
I can feel a thrash looming.
If I want to have this car on the track at the Flyin' Miata Open House in late August, I need to get a few things sorted. Time to get down to work!

The first step is the header. After some playing with pool tubing, I've managed to figure out the best hose routing and arrangement. It was very interesting work as I've never done anything quite like this before. My little Caterham model provided a certain amount of inspiration and confirmed my choice of where to pass through the frame. However, the engine in my car sits much further back than in a Caterham so it was only a starting point. I ended up arranging the pipes differently in the collector. Keith Armstrong also provided me with a link to a wonderful website showing two Caterham exhausts. Of course, I received his email after I'd come up with my design! It wouldn't have changed much, as you can see the difference in engine location from that page. But it has inspired me to try one more change to the #1 tube.

I also decided to pull the radiator to fix a small leak where I had moved one of the fittings. I didn't think this through completely and the entire cooling system drained onto the floor through the water pump outlet. Of course the car is too low to put any sort of pan under there at short notice...
entry 429

The first attempt at a header design.
The arrangement of pipes is the same as the Caterham 4-1 but it's going above the frame diagonal.
entry 430
Attempt number 2 at a header.
This is a basic copy of the Caterham 4-1.
entry 431
The best pipe arrangement for the header.
entry 432
The coolant drained out through the water pump inlet when I disconnected the hose!
I was concerned about the hose on the radiator. Whoops.
entry 433
<< | show individual entries | >>